Gen3i

Special features

---------PC integrated mainframeRobust and portable

Three slots for acquisition cardsAccepts any mix of GEN DAQacquisition cards

Up to 96 analog channels

200 MB/s continuous streamingSynchronized recording usingtwo GEN3i or GEN2i mainframesRemote use from external PCPerception Standard softwarewith Windows based userinterface for advanced reviewand analysis

The GEN3i is a versatile portable data

recorder. In addition, it provides all the featuresexpected from a transient recorder. The

hardware combines a full-featured, low-power,Intel Core™ i5 3rd generation Windows® PCwith a large, high-resolution, touch screen anda robust three-slot acquisition unit. The GEN3ihas the same form factor as its predecessorGEN2i, now offering more channels and moreprocessing power. The GEN3i comes with fivedifferent Windows® languages and eightdifferent Perception languages pre-installed.

Designed for operation in the field as well as inthe laboratory the GEN3i features a unique,Instrument Panel touch interface, with one-touch access to all features for daily operation.In addition, the GEN3i includes PerceptionStandard for post-processing. With a singletouch the data recorder turns into a dedicatedinstrument for analysis and sophisticatedreporting using the extra software options.

B3762-2.0 en

Data sheetGEN seriesGEN3i

GEN3i Block Diagram

Figure 1.1: Block Diagram GEN3i Portable Recorder

Windows® PC

MemoryProcessorEthernet

8 GB; DDR3 RAM

Intel 3610ME, Core™ i5 3rd generation; 2 Core, 4 threads; 2.7 GHz, 3.3 GHz turbo3 * RJ45 Ethernet connection; 1 Gbit/s

1 * RJ45 Ethernet connection with IEEE588 (PTP) support; 1 Gbit/s

1 * SFP based optical Ethernet connection with IEEE588 (PTP) support; 1 Gbit/s; supports850 and 1310 nm SFP modules.Supported on all Ethernet ports

Embedded 801.11b/g/n; , 100 and 300 Mbit/s; Wireless LAN can be hardware disabledUSB 2.0, 2 on back + 2 on front

USB 3.0, 4 on back (Using selective SSD > 100 MB/s continuous streaming)Solid State Drive (SSD), unformatted size 480 GB, 200 MB/s continuous streamingTFT SXGA touch screen, 17” / 1280x1024 resolution

2 * Display port and 1 * DVI-D connector; CRT 2048 x 1536 and DVI-D 1600 x 12003; clone mode and extended modeInternal speaker/jack plug 3.5 mmJack plug 3.5 mm

USB Keyboard and USB optical mouse

4; Direct recording control Start/Stop/Pause/Trigger

Wake on LANWireless LANUSB connectorsInternal storage PC diskDisplay

Video connectionMultiple monitors supportSpeaker/Speaker OutMicrophoneAccessoriesFront panel controls

Software

Instrument panel / Touch interface(Fully touch-optimized)DAQ softwareDAQ software options

DAQ Software and Instrument panel languagesOperating system

Operating system installed languages

Setup of instrument, Acquisition control, Display data: live / review, Basic measurements,Export and archiving, Basic reporting

Perception Standard package. Refer to Perception specification sheet for details.Analysis, Advanced Report, Video Playback, Multi Workbooks, Information, Basic FFT,Sensor Database and more

English, German, French, Chinese, Japanese, Korean, Russian, Portuguese (Brazilian)Microsoft Windows® 7 Ultimate

English, German, French, Chinese, Japanese

Other languages can be downloaded and installed using \"Windows® Update\"

HBM2B3762-2.0 en

Application Programmers Interfaces (API)

PNRF reader (free of charge)FunctionsCOM interface

Read PNRF, NRF and LRF recording files directly in your own application

The PNRF reader comes as COM interface and can be used from any application orprogramming language which supports COM automation

PNRF Software Development Kit (SDK)Matlab® integrationLabVIEW™ integrationFunctionsCOM interface

Available basic commandsExamples (free of charge)

LabVIEW™ integration (free of charge)CSI (Customer Software Interface)Functions

Installs PNRF dll’s and supplies Visual Basic, C# and C++ getting started examplesMatlab® PNRF reader install and example available within the PNRF SDKAvailable directly from National Instruments

Control Perception software from an external computer/application on Windows®, Linux,Unix, Mac OS X

All RPC commands have a COM wrapper for easier Windows® software integrationLoad and Save Perception setup files, Setup Recording, set and review Hardware Settings,Start/Stop/Pause/Trigger, monitor Live data

C++ and C# getting started example programs supplied for Windows®, source codeincluded. Unsupported Linux getting started example on request only.LabVIEW™ getting started example using RPC/COM available

Create software extension inside the Perception software by adding CSI user sheets,custom automation and extended analysis functions. Basic Windows C# sheet templateincluded. Available for all Microsoft .NET® 4 supporting languages.

Access to every Perception part: Start/Stop/Pause and Trigger, Start Manager, AcquisitionSystem, Hardware Settings, Displays, Meters, User Tables, Formulas, Calculations, DataManager, Data Sources, User variables, Notifications, Logging, Conversion Functions,Automation Actions, Sheet Manager and more, to create a dedicated application GUI thathides the entire Perception standard GUI

C# getting started example programs supplied, source code included

DCE/RPC (Distributed Computing Environment/Remote Procedure Calls)

Available basic controls & commands

Examples (free of charge)Training/Support Program

HBM offers paid professional training and support programs on all API interfaces (PNRF reader, RPC and CSI). Training program will be C#based, on-site or at central HBM location. On-site training can be customer specific. Support can be the development of a full custom softwareapplication or answering questions of software engineers.

Acquisition System

System Timebase and synchronizationCentral timebase for all acquisition cards

Accuracy

Base

Synchronization sources

± 3.5 ppm; aging after 10 years ± 10 ppmBinary, Decimal or External

IEEE1588:2008 (PTP V2: Precision Time Protocol; using 2 step master protocol)Master/Slave synchronization; Slave or single Master modeMultiple Master mode scheduled for Q3 2014IRIG and GPS scheduled for Q3 2014

Synchronization accuracy reduces as network traffic increases on Ethernet port used forPTP synchronization

± 150 ns; < 10% load no Ethernet switch used± 500 ns; < 50% load no Ethernet switch used± 5 μs; < 80% load no Ethernet switch used

To avoid excessive network traffic blocking the PTP synchronization, separate thecommunication and PTP synchronization on two independent networks.

Use 2 step master PTP aware switches to obtain best results across switches. Actual

accuracy depends on switch used. The use of switches without PTP support will create anunpredictable accuracy.

PTP synchronization accuracy

Acquisition Slots

Unused slots must be covered using the GEN DAQ blank panel. This closes the mainframe front panels for EMC/EMI and safety compliancebut also regulates the internal airflow for correct cooling of the acquisition system.

Maximum slotsAcquisition boards

Digital Event/Timer/Counter connector

3

All slots support any combination of GEN DAQ Acquisition boards1; Connected to slot A and B

B3762-2.0 en3HBM

Acquisition System

Thermal control

Every acquisition board and the acquisition system monitors its own temperatures andstatus. This is used to regulate fan speeds and reduce noise while optimizing airflow andpower consumption.

Any changes to the acquisition system configuration may change its internal thermal

gradients. As accurate calibration relies on a steady and repeatable thermal environment,calibration will be void if changes are made in the configuration. See the individual cardspecifications for calibration impact.

Calibration

GEN3i Connection Overview

Figure 1.2: GEN3i Connection Overview

HBM4B3762-2.0 en

Master/Slave Synchronization

Mainframe to mainframe phase shiftLED signalingMaster modeSlave mode

Basic synchronization

First sample

Synchronized timebaseChannel trigger exchange

Extended synchronization

Maximum number of mainframesSynchronous recording actionsSynchronous manual trigger

Compatibility

2 (Can be used in mix with GEN2i, GEN3i and GEN3t mainframes)

Start/Stop and Pause of a recording across multiple mainframes each controlled by aseparate Perception. Stop recording is a non synchronous actionUser action within Perception to trigger all mainframes synchronously

Basic synchronization features are backward compatible with GEN Series Master/Slavecard option for both Master and Slave modes. Extended synchronization features are notsupported by the Master/Slave card option. When using a mixed setup the system willautomatically work with basic synchronization only

Synchronizes the first sample in the recording for each mainframePrevents frequency drift of the sample rates within each mainframe

Synchronously exchanges every channel trigger connected to the Master/Slave trigger busto/from each connected mainframe± 100 ns

Optical link synchronized, not connected, function disabled

Basic and extended synchronization supported; 1 Slave maximum. Multiple slave supportedby Multi Slave option (Available Q3 2014)Basic and extended synchronization supported

Probe Calibration

PinsSignal

Signal amplitude

2; Signal and ground~1 kHz square wave0 V to 2 V using 1 MΩ load0 V to 1 V using 50 Ω load

B3762-2.0 en5HBM

I/O Connector

Figure 1.3: Pin assignment I/O Connector

Connector typeMating connector typeBreakout cable (included)Cable typeConnector typeLength

External Timebase In

Pulse width

Maximum frequency

Active edge

Rounding resolution

Coax

6; BNC female0.5 m (1.6 feet)

TTL compatible, Low -30 V to 0.7 V, High 2 V to 30 V100 ns min.5 MHzRising

4.01 µs; 250 kS/s and 20 kS/s acquisition cards1.01 µs; 1 MS/s and 200 kS/s acquisition cards510 ns; 2 MS/s and 200 kS/s (GN611) acquisition cards60 ns; 100 MS/s and 25 MS/s acquisition cards

Input to sample moment delayInput overvoltage protection

External Trigger In

Resolution

Minimum pulse width

Active edge

Input overvoltage protection

Delay(1)

Send to External Trigger OutTop Dead Center Rotational input

External Trigger Out

Active levelPulse width

Output impedanceShort circuit protected

Delay(1)

350 – 400 ns, plus maximum 1 full \"rounding resolution\"± 30 V DC

TTL compatible, Low -30 V to 0.7 V, High 2 V to 30 V50 ns500 ns

Selectable rising or falling± 30 V DC

± 1 μs + maximum 1 sample period (for decimal and binary time base)User can select to forward External Trigger In to the External Trigger Out BNCUsed to indicate top dead center in rotational external timebaseTTL compatible; 0 V < Low < 0.6 V; 2 V < High < 5 VSelectable High/Low/Hold High

High or Low selected: 12.8 µs

Hold High selected : Active from first trigger to end of recording49.9 Ω ± 1 %Continuous

516 ± 1 μs + maximum 1 sample period when Clock base: decimal, Filter: wideband(2)504 ± 1 μs + maximum 1 sample period when Clock base: binary, Filter: wideband(2)

(1)(2)

Delays are equal for all acquisition cards.

If analog and/or digital filter is used extra delay will be added depending on type of filter and signal frequency.

Tyco: 2-5747706-0 (D-sub, 9 pin female)Tyco: 5-747904-5

HBM6B3762-2.0 en

I/O Connector

External Event Out

FunctionActive levelPulse width

Output impedanceShort circuit protected

Delay(1)

External Start In

Minimum Pulse width

Active edge

Start response time

Input overvoltage protection

External Stop In

Minimum Pulse width

Active edge

Stop response time

Input overvoltage protection

(1)(2)

Delays are equal for all acquisition cards.

If analog and/or digital filter is used extra delay will be added depending on type of filter and signal frequency.

TTL compatible; 0 V < Low < 0.6 V; 2 V < High < 5 VSelectable Alarm or Recording Active outputSelectable High/Low for Alarm outputRecording active High output

Alarm: Active from start of alarm condition until condition endsRecording: Active until recording stops49.9 Ω ± 1 %Continuous

515 ± 1 μs + maximum 1 sample period when Clock base: decimal, Filter: wideband(2)503 ± 1 μs + maximum 1 sample period when Clock base: binary, Filter: wideband(2)TTL compatible, Low -30 V to 0.7 V, High 2 V to 30 V200 ns

Rising/falling edge; software selectableTypically 1 s when system is completely idle± 30 V DC

TTL compatible, Low -30 V to 0.7 V, High 2 V to 30 V200 ns

Rising/falling edge; software selectable

Typically 1 s when system is recording without automation± 30 V DC

Digital Event/Timer/Counter

Figure 1.4: Digital Event/Timer/Counter block diagram

Supported CardsNumber of ConnectorsConnector TypeCable Connector TypeOutput Power

Voltage

Maximum current

Event Inputs

Number of events

Levels

16 per card, 2 cards per connector

TTL Compatible, Low -30 V to 0.7 V, High 2 V to 30 V5 ± 0.5 V DC0.5 A

See specifications of acquisition cards1

44 pin, female D-type connector, AMP HD-22 series (Tyco: 5748482-5)44 pin, male D-type connector, HDP-22 series (Tyco: 1658680-1)

B3762-2.0 en7HBM

Digital Event/Timer/Counter

Figure 1.5: Logic threshold voltage levels

Overvoltage protection

Timer/Counter

Number of channels

Functions

Outputs

Number of outputs

FunctionsOutput levelsOutput resistanceOutput current

Two per card, two cards per connector

See specifications of acquisition cards that support these outputsTTL compatible; 0 V < Low < 0.6V; 2 V < High < 5 V49.9 Ω ± 1 %

20 mA, short circuit protected

Two per card, two cards per connector

See specifications of acquisition cards that support these inputs± 30 V DC

Digital Event/Timer/Counter Connector Pin Assignment

Figure 1.6: Pin diagram for Digital Event/Timer/Counter connector

QuantumX Power Supply

Connector typeMating connector typeConnector pinningOutput PowerOutput Voltage

Maximum Output Current

ODU, G81L0C-P08LFG0-0000ODU, SX1LOC−P08MFG0−0000Only GND and PWR signal connected15 Watt

> 11 V; Typical 11.5 V to 12 V

1.4 A; Current limited and short circuit protected

HBM8B3762-2.0 en

Power

Power Inlet

Total Power of unit (maximum)

47-63 Hz, 100-240 V AC250 VA, 300 VA peak

Physical, Weight and Dimensions

Weight

Mainframe

Dimensions

Height/Height with handle

WidthDepth

Acoustic NoiseTemperature SensorsCooling FansHandleTilting FeetGroundingCasingAccessories

34.2 cm/39.2 cm (13.5\"/15.4\")43.6 cm (17.2\")18.6 cm (7.3\")

The total A-weighted SPL 55 dBA @ 0.6 m maximumTemperature for monitoring and air flow control2

One carrying handle, also used for higher tilt anglesTwo retractable feet for small tilt angles4 mm Banana plugAluminum/Plastic cover

Soft carry case with strap for transportation included with hardened front and back forprotection, and storage pouches for mouse and keyboard9 kg (20.9 lbs), add ≈ 1 kg (2.2 lbs) per acquisition board installed

Figure 1.7: GEN3i Dimensions

B3762-2.0 en9HBM

Environmental Specifications

Temperature Range

Operational

Non-operational (Storage)

Thermal protection

Relative humidityProtection classAltitude

Shock: IEC 60068-2-27

OperationalNon-operational

Vibration: IEC 60068-2-34

OperationalNon-operational

Operational Environmental Tests

Cold test IEC60068-2-1 Test AdDry heat test IEC-60068-2-2 Test BdDamp heat test IEC60068-2-3 Test Ca

Non-Operational (Storage) Environmental Tests

Cold test IEC-60068-2-1 Test AbDry heat test IEC-60068-2-2 Test Bb

Change of temperature test

IEC60068-2-14 Test NaDamp heat cyclic test

IEC60068-2-30 Test Db variant 1

-25 °C (-13 °F) for 72 hours

+70 °C (+158 °F) humidity <50 % RH for 96 hours-25 °C to +70 °C (-13 °F to +158 °F)

5 cycles, rate 2 to 3 minutes, dwell time 3 hours+25 °C/+40 °C (+77 °F/+104 °F), humidity >95/90 % RH6 Cycles, cycle duration 24 hours-5 °C (+23 °F) for 2 hours+40 °C (+104 °F) for 2 hours

+40 °C (+104 °F), humidity >93 % RH for 4 days1 g RMS, ½ h; 3-axis, random 5 to 500 Hz2 g RMS, 1 h; 3-axis, random 5 to 500 Hz

Half-sine 10 g/11 ms; 3-axis, 1000 shocks in positive and negative directionHalf-sine 25 g/6 ms; 3-axis, 3 shocks in positive and negative direction0 °C to +40 °C (+32 °F to +104 °F)-25 °C to +70 °C (-13 °F to +158 °F)

Automatic thermal shutdown at 85 °C (+185 °F) internal temperatureUser warning notifications at 75 °C (+167 °F)0 % to 80 %; non-condensing; operationalIP20

Maximum 2000 m (6562 feet); operational

Harmonized Standards for CE Compliance, according to the following directives

Low voltage directive (LVD): 2006/95/EC

Electromagnetic compatibility directive (EMC): 2004/108/ECElectrical SafetyEN 61010-1 (2010)EN 61010-2-030 (2010)EN 61326-1 (2006)EMISSIONEN 55011

Industrial, scientific and medical equipment - Radio-frequency disturbance characteristics - Limits and methods ofmeasurement

Conducted disturbance: class B; Radiated disturbance: class ALimits for harmonic current emissions: class D

Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systemsElectrostatic discharge immunity test (ESD);

contact discharge ± 4 kV/air discharge ± 8 kV: performance criteria BRadiated, radio-frequency, electromagnetic field immunity test;80 to 2700 MHz using 10 V/m, 1000 Hz AM: performance criteria A

Electrical fast transient/burst immunity test

Mains ± 2 kV using coupling network. Channel ± 2 kV using capacitive clamp: performance criteria B

Surge immunity test

Mains ± 0.5 kV/± 1 kV Line-Line and ± 0.5 kV/± 1 kV/± 2 kV Line-earth Channel ± 0.5 kV/± 1 kV using couplingnetwork: performance criteria B

Immunity to conducted disturbances, induced by radio-frequency fields

0.15 to 80 MHz, 1000 Hz AM; 10 V RMS @ mains, 3 V RMS @ channel, both using clamp: performance criteria AVoltage dips, short interruptions and voltage variations immunity testsDips: performance criteria A; Interruptions: performance criteria C

Safety requirements for electrical equipment for measurement, control, and laboratory use - General requirementsParticular requirements for testing and measuring circuits

Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 1: General requirements

Electromagnetic Compatibility

EN 61000-3-2EN 61000-3-3IMMUNITYEN 61000-4-2EN 61000-4-3EN 61000-4-4EN 61000-4-5

EN 61000-4-6EN 61000-4-11

HBM10B3762-2.0 en

IRIG, IRIG/GPS (options, to be ordered separately; available Q2 2014)

IRIG(1)

Supported by IRIG and IRG/GPS optionTime Code Translator (Input)

Time Code formatsModulation ratioInput amplitudeInput impedance

Time Code Output

Time Code formatModulation ratioOutput amplitude

DC level shift

AM modulated input/output connectorsDCLS connector

Time synchronization accuracyGEN DAQ series functions

IRIG B, IEEE 1344 compliant3:1

4 V Peak-to-Peak (fixed) into 50 ΩTTL/CMOS

2 SMB sockets; one for input and one for output

Micro DP, 15-pin; some signals internally linked to Interface/Controller Module<5 µs modulated, <1 µs (DCLS)

Capture start of recording time

Synchronize Master Time Base oscillator frequency

No recording active

Recording or pause active

User notifications while recordingShort term tracking stabilityLong term tracking “Fly-wheeling”GPS(1)

Only supported by IRG/GPS optionGPS connectorGPS antennaGPS antenna cable

Time synchronization accuracyGEN DAQ series functionsGPS localization time

No recording active

Recording or pause active

User notifications while recordingShort term tracking stabilityLong term tracking “Fly-wheeling”(1)

Requires factory installation

Micro DP, 9-pin1; included

50 m (1 feet); included<1 µs

Capture start of recording time

Synchronize Master Time Base oscillator frequency2 to 15 minutes1 to 10 minutes

1 to 10 minutes plus 25 s per ms recording time deviation from IRIG timeTime marks on GPS satellites lost/restored and GPS time synchronized5.0 E-85.0 E-71 to 5 minutes

1 to 5 minutes plus 25 s per ms recording time deviation from IRIG timeTime marks on IRIG signal lost/restored and IRIG time synchronized5.0 E-85.0 E-7

IRIG A and IRIG B, IEEE 1344 compliantAM Modulated or DC level shift (DCLS)3:1 to 6:1

500 mV to 5 V Peak-to-Peak>10 kΩ

Time required to full synchronization after IRIG signal detected

Time required to full synchronization after GPS localization completed

Multiple Slave Card (option, available Q3 2014)

In Master mode enables the synchronization of 2 or more Slaves. Single Slave control and Slave mode supported by mainframe Synchronizationconnector. Specifications to be determined

B3762-2.0 en11HBM

Shipping Case (option, to be ordered separately)

Figure 1.8: Hardcover reusable shipment case with wheels and transport handle

Outside DimensionsWeight Empty CaseSystem Storage AreaAccessories AreaReliable Case TransportCase ExtrasShock and VibrationDrop Test

60.0 cm (23.6\") x 32.5 cm (12.8\") x 67.5 cm (26.5\") (H x W x D)16.5 kg (36.3 lbs)

Special area for system, slides in from the top for easy storage and removal from theshipment case. Protects the system for impact during drop, shock and vibrationsSeparate area for keyboard, mouse, power cable and some cables

Wheels and extendable handle constructed for stable transportation with low gravitationpoint to avoid tumbling of case in any direction during roll transportTwo lift handles and locks on side of the case for easy transportTested with system inside case according to ASTM D4728 ETested with system inside case according to ASTM D4169-04 Level I

Rack Mount Kit (option, to be ordered separately)

Figure 1.9: GEN3i Rack Mount Kit

Rack Mount Kit

Mounting GEN3i mainframe in a standard 19” rack. Does not support the mouse andkeyboard delivered with the GEN3i. Requires no additional mounting materials. Userinstalled option.

HBM12B3762-2.0 en

Txx Adapter (option, to be ordered separately)

Connects a T12 or similar torque transducer to GEN2i, GEN3i and GEN3t Digital Event Timer/Counter connector

Figure 1.10: Txx adapter block diagram

Txx Connection

Number of Txx Torque transducers

Torque interface supportSpeed interface support

Txx signals

LevelsTermination

Differential RS422100 Ω2

Torque and ShuntRPM and Direction

B3762-2.0 en13HBM

Txx Adapter (option, to be ordered separately)

Connects a T12 or similar torque transducer to GEN2i, GEN3i and GEN3t Digital Event Timer/Counter connectorConnectors

GEN series interfaceLoop through event input

Torque interfaceSpeed/RPM interface

Cables

Txx adapter to GEN2i/GEN3i/GEN3t

Txx adapter to Txx TorqueTxx adapter to Txx Speed/RPM

Power

Adapter

Txx Torque transducers

Outside dimensions

Power by GEN2i/GEN3i/GEN3tRequires separate power supply

2.15 (.60”) x 171.6 (6.76”) x 123.6 (4.86) (H x W x D)0.5 m (1. Feet), included with Txx adapter

1-KAB149-6 (other lengths available), to be ordered separately1-KAB163-6 (other lengths available), to be ordered separatelyHD22 sub-D 44 pin male (connecting cable included)

44 pin, female D-type connector, AMP HD-22 series (Tyco: 5748482-5)15 pin, female sub-D type (matches 1-KAB149-6)15pin, female sub-D type (matches 1-KAB163-6)

Figure 1.11: Txx adapter dimensions

HBM14B3762-2.0 en

Acquisition Cards

ModelBasic200kBasic200k XT ISOBasic1MBasic1M ISOBasic1M XT ISOBridge200k ISOBridge1M ISOUni200k ISOUni1M ISOBasic20k-16Basic20k-32HiRes250k-16HiRes250k-32HiSpeed 25MHiSpeed 100MFiber100M 6600Fiber100M 7600Iso1kV200kIso1kV2MMarker1MMarker1M HV(1)(2)(3)(4)

TypeSingle Ended

Unbalanced DifferentialSingle Ended

Unbalanced DifferentialUnbalanced DifferentialBridge/DifferentialBridge/DifferentialDifferential/IEPE/ShuntDifferential/IEPE/ShuntDifferentialDifferential

Differential/IEPE/ChargeDifferential/IEPE/ChargeDifferential/Single EndedDifferential/Single EndedOptical FiberOptical FiberBalanced DifferentialBalanced DifferentialBinaryOptical/Binary

Isolationnoyesnoyesyesyesyesyesyesnonononononoyesyesyesyesnoyes & no

Max. SR(1)200 kS/s200 kS/s1 MS/s1 MS/s1 MS/s200 kS/s1 MS/s200 kS/s1 MS/s20 kS/s20 kS/s250 kS/s250 kS/s25 MS/s100 MS/s100 MS/s100 MS/s200 kS/s2 MS/s1 MS/s1 MS/s

Resolution16 bit16 bit16 bit16 bit16 bit16 bit16 bit16 bit16 bit16 bit16 bit16/24 bit16/24 bit15 bit14 bit--(4)--(4)16/18 bit16/18 bit1 bit1 bit

Memory(2)128 MB128 MB256 MB512 MB512 MB128 MB512 MB128 MB512 MB200 MB200 MB1800 MB1800 MB128 MB1800 MB1800 MB1800 MB200 MB1800 MB512 MB512 MB

Channels88888444416321632444(4)4(4)668 & 32

Event, T/C(3)0, 00, 00, 00, 00, 00, 00, 00, 00, 016, 016, 016, 216, 20, 00, 00, 00, 016, 216, 20, 00, 0

Maximum Sample Rate/channel (not multiplexed).Total recording memory/card.

Digital Events, Timer/Counter channels (Supported by GEN3i and GEN2i Digital Event/Timer/Counter connector only).This card supports maximum four optical fiber transmitter channels.

Optical Fiber Transmitter Channels

Transmitter

Every transmitter is a single channel unit. Every unit has an unbalanced differential input, amplifier, analog anti alias filter and ADC with anoptical data and control link to the receiver card. The receiver card has the recording logic, sample rate selection and memory.ModelHV6600 100MHV6600 25MMV6600 100MMV6600 25M7600 100M

Receiver CardFiber100M 6600Fiber100M 6600Fiber100M 6600Fiber100M 6600Fiber100M 7600

PowerBatteryBattery120/240 V AC120/240 V ACExternal 12 V DC

Sample rate100 MS/s25 MS/s100 MS/s25 MS/s100 MS/s

Resolution14 bit15 bit14 bit15 bit14 bit

Isolation

User application definedUser application defined1800 V RMS1800 V RMS

User application defined

Special Function Cards

5B Carrier

Uses one GEN DAQ slot, holds up to six 5B modules. 5B modules, I/O connectors andcabling not included. An acquisition card is required for actual recording.

The 5B Series signal conditioning modules provide a low cost method of connecting analogsignals with data acquisition systems. They are designed to convert thermocouples, RTD's,strain gages, frequencies, potentiometers, slide wires and other signals into standardized,isolated analog outputs.

B3762-2.0 en15HBM

Ordering Information(1)Article

GEN3i

Description

GEN3i rugged, portable data recorder.(2)

Integrated Instrument, with three acquisitionsslots, 200 MB/s streaming rate, one Master/Slaveconnector, integrated PC, Windows® 7 Ultimate, bit version. 17 inch touch screen TFT,480 GB Solid State Disk, Mouse, Keyboard,carrying bag with integrated protective frontcover. Includes Perception Standard softwarepackage.

GEN3i - 6 channel Iso1kV200k package.

Same as GEN3i plus one 1-GN611-2; 6 channel,1 kV isolated balanced differential inputs,200 kS/s, 128 MB RAM cards.

GEN3i - 12 channel Iso1kV200k package.

Same as GEN3i plus two 1-GN611-2; 6 channel,1 kV isolated balanced differential inputs,200 kS/s, 128 MB RAM cards. (12 channelstotal).

GEN3i - 18 channel Iso1kV200k package.Same as GEN3i plus three 1-GN611-2; 6channel, 1 kV isolated balanced differentialinputs, 200 kS/s, 128 MB RAM cards. (18channels total).

Order No.

1-GEN3i-2

GEN3i plus oneIso1kV200k card

1-GEN3i6-2

GEN3i plus twoIso1kV200k cards

1-GEN3i12-2

GEN3i plus threeIso1kV200k cards

1-GEN3i18-2

(1)(2)

All GEN series systems are intended for exclusive professional and industrial use.

GEN3i ships with keyboard layout in English, German, French, Chinese or Japanese. Specify on order.

HBM16B3762-2.0 en

Options, to be ordered separatelyArticle

IRIG PMC card

Description

Factory installed option.

GEN DAQ IRIG interface fits into open XMC/PMC slot of GEN DAQ Interface/Controllermodule.

Cannot be used in combination with 10 GbitEthernet XMC card.

Factory installed option.

GEN DAQ IRIG/GPS interface fits into openXMC/PMC slot of GEN DAQ Interface/Controllermodule, comes with antenna and 15 m cable.Cannot be used in combination with 10 GbitEthernet XMC card.

GEN DAQ 1GBit Ethernet SFP, 850 nm MultiMode, up to 500 m optical cable lengthsupported, LC connector support.

1 Gbit SFP modules are not compatible with the10 Gbit SFP+ modules.

GEN DAQ 1Gbit Ethernet SFP, 1310 nm SingleMode, up to 10 km optical cable lengthsupported, LC connector support.

1 Gbit SFP modules are not compatible with the10 Gbit SFP+ modules.

Factory installed option.

GEN DAQ 10 Gbit Ethernet XMC card adds upto 2 extra 10 Gbit Ethernet network connectionsto a GEN DAQ series mainframe. Supports up to200 MB/s continuous data transfer from the GENDAQ mainframe to an appropriate PC. Requiresa 10 Gbit optical network SFP+ module. Cannotbe used in combination with IRIG or IRIG/GPSPMC card.

Order No.

1-G001-1Available Q22014

IRIG/GPS PMCcard

1-G002-2Available Q22014

1 Gbit OpticalNetwork SFPmodule 850 nm

1-G062-2

1 Gbit OpticalNetwork SFPmodule 1310 nm

1-G063-2

10 Gbit EthernetXMC card

1-G0-2Available Q22014

10 Gbit OpticalNetwork SFP+module 850 nm

GEN DAQ 10Gbit Ethernet SFP+, 850 nm MultiMode, up to 66 m optical cable length supported,LC connector support.

10 Gbit SFP+ modules are not compatible withthe 1 Gbit SFP modules.

GEN DAQ 10Gbit Ethernet SFP+, 1310 nmSingle Mode, up to 10 km optical cable lengthsupported, LC connector support.

10 Gbit SFP+ modules are not compatible withthe 1 Gbit SFP modules.

1-G065-2Available Q22014

10 Gbit OpticalNetwork SFP+module 1310 nm1-G066-2Available Q22014

B3762-2.0 en17HBM

Accessories, to be ordered separatelyArticle

GEN2i/GEN3i

19 inch rack mountkit

Description

GEN2i/GEN3i rack mount kit (does not includemouse and keyboard mountings).User installed option.

Order No.

1-G053-2

GEN2i/GEN3i/GEN3t shippingcase

GEN2i/GEN3i/GEN3t shipping case, with wheelsand handle Tested according to ASTM D4169-04Level I (drop), and ASTM D4728 E (vibration &shock)

Gross weight (empty) 16.5 kg (36.3 lbs).

1-G0-2

Fiber optic MultiMode standardcable

GEN DAQ standard indoor zipcord fiber opticduplex Multi Mode 50/125 µm cable, 3.0 dB/kmloss, LC-LC connectors, orange, ISO/IEC 11801type OM2.

Used with 850 nm optical 1 Gbit or 10 Gbit

Ethernet. (1-G062-2 and 1-G065-2) and Master/Slave synchronizations.

Lengths 3, 10, 20 and 50 meter (10, 33, 66 and1 feet)

GEN DAQ standard indoor zipcord fiber opticduplex Single Mode 9/125 µm cable, 0.5 dB/kmloss, LC-LC connectors, yellow, ISO/IEC 11801type OS1.

Used with 1310 nm optical 1 Gbit or 10 GbitEthernet (1-G063-2 and 1-G066-2).

Lengths 2, 10, 20, 50 and 100 meter (6.5, 33, 66,1 and 328 feet)

GEN DAQ heavy duty indoor/outdoor fiber opticduplex Single Mode 9/125 µm cable, 0.5 dB/kmloss, LC-LC connectors, black, ISO/IEC 11801type OS1.

Used with 1310 nm optical 1 Gbit or 10 GbitEthernet (1-G063-2 and 1-G066-2).

Lengths 10, 20, 50, 100, 150 and 300 meter (33,66, 1, 328, 492 and 984 feet)

GEN DAQ 5B Carrier. Uses one GEN DAQ slot,holds up to six 5B modules. 5B modules, I/Oconnectors and cabling not included. Basic cardrequired for acquisition.

1-KAB280-31-KAB280-101-KAB280-201-KAB280-50

Fiber optic SingleMode standardcable

1-KAB288-21-KAB288-101-KAB288-201-KAB288-501-KAB288-100

Fiber optic SingleMode heavy dutycable

1-KAB2-101-KAB2-201-KAB2-501-KAB2-1001-KAB2-1501-KAB2-300

5B carrier card1-G028-2

TXX adapter

TXX adapter. Converts the differential signalingused by HBM torque transducers to TTL signallevels used by the timer counter A and B availableon the Digital Event/Timer/Counter connector.Event output connected to Shunt control. Allevent TTL signals available on output connector.Comes with 1 m (3.3 feet) cable to connectadapter to your mainframe. Torque transducercables not included.

1-G070-2

HBM18B3762-2.0 en

Software Options, to be ordered separately(1)ArticleDescription

Order No.

Perception AdvancedSame as Perception Standard but includes the options:

1-PERC-AD-01-2Analysis, Reports, Info Sheets, Exports, Workbooks and Video Playback.Perception Professional

Same as Perception Standard but includes the options

1-PERC-PRO-01-2

Analysis, Reports, Info Sheets, Exports, Workbooks, Video Playback, Basic FFTand Sensor Database.

Perception EnterpriseSame as Perception Professional but runs on native bits Windows® XP, Vista,1-PERC-E-01-2

7 and 8 only. This version supports the use of more than 2 GByte memory inyour PC. Specifically important for systems using multiple mainframes, extensiveuse of the FFT option and/or large amounts of calculations.

Perception Viewer

Same as Perception Standard but without mainframe setup and control.1-PERC-VW-01-2Perception Viewer AdvancedSame as Perception Advanced but without mainframe setup and control.1-PERC-VA-01-2AnalysisAnalysis includes +, -, *, /, max, min, RMS and filters using a formula database.1-PERC-OP-AN-01-2ReportingCreate professional reports including displays, tables, text, graphics.1-PERC-OP-RP-01-2ExportsAdditional export formats added to Perception.

1-PERC-OP-MEX-01-2Info sheetsAllows custom entries and variable definitions to be stored with data.1-PERC-OP-IS-01-2Multiple WorkbooksSimultaneous multiple display windows on multiple monitor systems.1-PERC-OP-MWB-01-2Video PlaybackSimultaneous playback of standard video files.

1-PERC-OP-VP-01-2Basic FFT

Live FFT while recording (hardware dependent) and Review FFT.1 -PERC-OP-BFFT-01Multiple MainframesSimultaneous control of multiple GEN DAQ mainframes.

1-PERC-OP-MMF-01-2Sensor DatabaseCollection of sensors' information, simplifies the set-up of an acquisition channel.1-PERC-OP-SDB-01-2CSI InterfaceAllows the development of and running CSI programs.

1-PERC-OP-CSI-01-2RPC/COMRemote control of Perception, including basic hardware setup and control.1-PERC-OP-IF-01-2BE256/MP controlTo control a single BE256 or a single MultiPro from Perception via IEEE4881-PERC-OP-BE-01-2interface.

SEQUENCETo control BE3200 Test Sequencer from Perception via USB port.1-PERC-OP-SEQ-01-2Requires Perception Standard or higher (1-PERC-ST-01-2).

STL Analysis

Special analysis routines according to the STL standard used in LV, MV and HV1-PERC-OP-STL-01-2

labs. Includes import of TGD data (Test Data Generator) for verification.Requires Analysis option (1-PERC-OP-AN-01-2).

HPHV-AAHighPower/HighVoltage automated analysis. Evaluates data of NoLoad,1-PERC-OP-HHP-01-2

ShortCircuit, Capacitive and Synthetic tests of HV/MV switchgear devices(requires signals from tripping coils and travel to be recorded).Requires STL Analysis option (1-PERC-OP-STL-01-2).

HV-IAHigh Voltage Impulse Analysis option; evaluates Lightning, Switching and1-PERC-OP-HIA-01-2

Current impulses; designed according to IEC60060-1 and IEC61083-2requirements. Allows evaluation with new k-factor method.

eDriveAllows easy and application oriented setup and efficiency calculations of1-PERC-OP-EDR-01-2

electrical inverter / drive tests with minimum interaction.

(1)

Software options are also sold in multiple licenses packages and multiple network license seats.

©Hottinger Baldwin Messtechnik GmbH. All rights reserved.All details describe our products in general form only.

Hottinger Baldwin Messtechnik GmbH

They are not to be understood as express warranty and donot constitute any liability whatsoever.

Im Tiefen See 45 ∙ 293 Darmstadt ∙ GermanyTel. +49 6151 803-0 ∙ Fax: +49 6151 803-9100E-mail: info@hbm.com ∙ www.hbm.com

measure and predict with confidence

ne 0.2-2673B